Weld Zone Material Characterisation Based on Spherical Indentation Data

Weld Zone Material Characterisation Based on Spherical Indentation Data

S. Syngellakis H. Habbab B.G. Mellor

Wessex Institute, UK

University of Southampton, UK

Page: 
527-539
|
DOI: 
https://doi.org/10.2495/CMEM-V6-N3-527-539
Received: 
N/A
| |
Accepted: 
N/A
| | Citation

OPEN ACCESS

Abstract: 

An improved elasto-plastic characterisation technique relying on instrumented indentation data, accounting for frame compliance, spherical indenter imperfections and, most importantly, material pile-up at indentation edges was validated on experimental data from control specimens with known properties. The method was subsequently applied to the characterisation of weld regions for which traditional testing methods are not applicable. Variations of elasto-plastic properties were obtained from indentations on a butt-welded steel specimen spanning the three distinct weld regions. The consistency of these results and their sensitivity to variations of experimental data was examined and discussed.

  References

[1] Tabor, D., A simple theory of static and dynamic hardness. Proceedings, Royal Society of London, Series A: Mathematical and Physical Sciences, 192, pp. 247–274, 1948. https://doi.org/10.1098/rspa.1948.0008

[2] Doerner, M.F. & Nix, W.D., A method for interpreting the data from depth-sensing indentation instruments. Journal of Materials Research, 1(4), pp. 601–609, 1986. https://doi.org/10.1557/jmr.1986.0601

[3] Sneddon, I.N., The relation between load penetration in the axisymmetric Boussinesq problem for a punch of arbitrary profile. International Journal of Engineering Science, 3(1), pp. 47–57, 1965.https://doi.org/10.1016/0020-7225(65)90019-4

[4] Ghosh, S., Pal, T.K., Mukherjee, S., Das, G. & Ghosh, S., Comparative study of heataffected zone with weld and base material after post-weld heat treatment of HSLA steel using ball indentation technique. Journal of Materials Science, 43(16), pp. 5474–5482, 2008.https://doi.org/10.1007/s10853-008-2840-6

[5] Pharr, G.M., Oliver, W.C. & Brotzen, F.R., On the generality of the relationship among contact stiffness, contact area, and elastic modulus during indentation. Journal of Materials Research, 7(3), pp. 613–617, 1992.https://doi.org/10.1557/jmr.1992.0613

[6] Bolshakov, A., Oliver, W.C. & Pharr, G.M., Influences of stress on the measurement of mechanical properties using nanoindentation: Part II. Finite element simulations. Journal of Materials Research, 11(3), pp. 760–768, 1996. https://doi.org/10.1557/jmr.1996.0092

[7] Matthews, J.R., Indentation hardness and hot pressing. Acta Metallurgica, 28(3), pp. 311–318, 1980.https://doi.org/10.1016/0001-6160(80)90166-2

[8] Hill, R., Storakers, B. & Zdunek, A.B., A theoretical study of the Brinell hardness  test. Proceedings of the Royal Society of London Series A: Mathematical Physical and Engineering Sciences, 423(1865), pp. 301–330, 1989. https://doi.org/10.1098/rspa.1989.0056

[9] Taljat, B., Zacharia, T. & Kosel, F., New analytical procedure to determine stress-strain curve from spherical indentation data. International Journal of Solids and Structures, 35(33), pp. 4411–4426, 1998.https://doi.org/10.1016/s0020-7683(97)00249-7

[10] Habbab, H., Mellor, B.G. & Syngellakis, S., Post-yield characterisation of metals with significant pile-up through spherical indentations. Acta Materialia, 54, pp. 1965–1973, 2006.https://doi.org/10.1016/j.actamat.2005.12.021

[11] Habbab, H., Post-yield characterisation of welds based on instrumented hardness tester data. PhD Thesis, University of Southampton, 2005.

[12] Herbert, E.G, Pharr, G.M, Oliver, W.C, Lucas, B.N. & Hay, J.L., On the measurement of stress–strain curves by spherical indentation. Thin Solid Films, 398–399, pp. 331–335, 2001.https://doi.org/10.1016/s0040-6090(01)01439-0