Numerical Simulation of Flash-Boiling Through Sharp-Edged Orifices

Numerical Simulation of Flash-Boiling Through Sharp-Edged Orifices

Konstantinos Lyras Siaka Dembele Elena Vyazmina Simon Jallais Jennifer Wen

Kingston University London, Department of Mechanical and Automotive Engineering, London, UK

Air Liquide – Centre de Recherche Paris-Saclay, France

University of Warwick, School of Engineering, Coventry, UK

 

Page: 
176-185
|
DOI: 
https://doi.org/10.2495/CMEM-V6-N1-176-185
Received: 
N/A
| |
Accepted: 
N/A
| | Citation

OPEN ACCESS

Abstract: 

its vapour pressure. Flashing of a flowing liquid through an orifice or a nozzle can occur either inside or outside the nozzle depending on the local pressure and geometry. Vapour generation during flashing leads to interfacial interactions that eventually influence the jet.

Empirical models in the literature for simulating the interphase heat transfer employ many simplifying assumptions, which limits their applicability. Typical models, usually derived from cavitation, fail to describe the physics of heat and mass transfer, making them unreliable for flashing. The Homogeneous Relaxation Model (HRM) is a reliable model able to capture heat transfer under these conditions accounting for the nonequilibrium vapour generation. This approach uses a relaxation term in the transport equation for the vapour. On the basis of the generic compressible flow solver within the open source computational fluid dynamics (CFD) code OpenFOAM, the HRM has been implemented to create a dedicated new solver HRMSonicELSAFoam. An algorithm that links the standard pressure–velocity coupling algorithm to the HRM is used. In this method, a pressure equation is derived which employs the continuity equation includ ing compressibility effects. A relaxation term has been defined such that the instantaneous quality would relax to the equilibrium value over a given timescale. Although it is possible to consider this timescale constant, it is calculated via an empirical correlation in the present study.

Validations have been carried out by simulating twophase flows through sharpedged orifices. The relatively good agreement achieved has demonstrated that the solver accurately calculates the pressure and vapour mass fraction. This demonstrates the potential of HRMSonicELSAFoam for flash boiling simulations and predicting the properties of the subsequent flash atomisation.

Keywords: 

atomisation, CFD, flash boiling, thermal nonequilibrium

  References

[1] Arcoumanis, C., Gavaises, M. & French, B., Effect of fuel injection process on the structure of diesel sprays. SAE Technical Paper Series, 1997.

[2] Sher, E., BarKohany, T. & Rashkovan, A., Flashboiling atomisation. Progress in Energy and Combustion Science, 34(4), pp. 417–439, 2008. https://doi.org/10.1016/j.pecs.2007.05.001

[3] Rayleigh, L., On the pressure developed in a liquid during the collapse of a spherical cavity. Philosophical Magazine Series, 34, pp. 94–98, 1917. https://doi.org/10.1080/14786440808635681

[4] Plesset, M.S., In Cavitation in Real Liquids, R. Davies, Ed., Elsevier Publishing Company, Amsterdam, pp. 1, 1964.

[5] Kawano, D., Ishii, H., Suzuki, H., Goto, Y., Odaka, M. & Senda, J., Numerical study on flashboiling spray of multicomponent fuel. Heat Transfer: Asian Research, 35(5), pp. 369–385, 2006. https://doi.org/10.1002/htj.20117

[6] Giannadakis, E., Gavaises, M. & Arcoumanis, C., Modelling of cavitation in diesel injector nozzles. Journal of Fluid Mechanics, 616, pp. 153–193, 2008. https://doi.org/10.1017/s0022112008003777

[7] Salvador, F.J., Jaramillo, D., Romero, J.V. & Roselló, M.D., Using a homogeneous equilibrium model for the study of the inner nozzle flow and cavitation pattern in con vergent–divergent nozzles of diesel injectors. Journal of Computational and Applied Mathematics, 309, pp. 630–641, 2017. https://doi.org/10.1016/j.cam.2016.04.010

[8] Bilicki, Z. & Kestin, J., Physical aspects of the relaxation model in twophase flow. Proceedings of the Royal Society A: Mathematical, Physical and Engineering Sciences, 428, pp. 379–397, 1990. https://doi.org/10.1098/rspa.1990.0040

[9] DownarZapolski, P., Bilicki, Z., Bolle, L. & Franco, J., The nonequilibrium relaxation model for onedimensional flashing liquid flow. International Journal of Multiphase Flow, 22, pp. 473–483, 1996. https://doi.org/10.1016/03019322(95)00078x

[10] Lee, J., Madabhushi, R., Fotache, C., Gopalakrishnan, S. & Schmidt, D., Flashing flow of superheated jet fuel. Proceedings of the Combustion Institute, 32, pp. 3215–3222, 2009. https://doi.org/10.1016/j.proci.2008.06.153

[11] Schmidt, D.P., Gopalakrishnan, S. & Jasak H., Multidimensional simulation of thermal nonequilibrium channel flow. International Journal of Multiphase Flow, 36, pp. 284–292, 2010. https://doi.org/10.1016/j.ijmultiphaseflow.2009.11.012

[12] Sinha, A., Balasubramanian, S. & Gopalakrishanan, S., Internal and external char acteristics of a superheated jet. Computational Methods in Multiphase Flow, VIII,   pp. 225–236, 2015. https://doi.org/10.2495/mpf150201

[13] Kolev, N.I., Multiphase flow dynamics, Vol. 2 Thermal and mechanical interactions, 4th ed., Springer, Berlin, New York, Tokyo, ISBN 9783642205972, pp. 290, 2011.

[14] Weller, H., Tabor, G., Jasak, H. & Fureby, C., A tensorial approach to computational continuum mechanics using objectoriented techniques. Computers in Physics, 12(6), pp. 620–631, 1998. https://doi.org/10.1063/1.168744

[15] Reinke, P. & Yadigaroglu, G., Explosive vaporisation of superheated liquids by boiling fronts. International Journal of Multiphase Flow, 27, pp. 1487–1516, 2001. https://doi.org/10.1016/s03019322(01)000234

[16] Simoneau, R., Maximum twophase flow rates of subcooled nitrogen through a sharp edged orifice (NASA TM X71760), Cryogenic Engineering Conference Kingston, Ontario, July 22–25, 1975.

[17] Hervieu, E. & Veneau, T., Experimental determination of the droplet size and velocity distributions at the exit of the bottom discharge pipe of a liquefied propane storage tank during a sudden blowdown. Journal of Loss Prevention in the Process Industries, 9(6), pp. 413–425, 1996. https://doi.org/10.1016/s09504230(96)000307

[18] Senda, J., Hojyo, Y. & Fujimoto, H., Modeling on atomisation and vaporization process in flash boiling spray. JSAE Review, 15, pp. 291–296, 1994. https://doi.org/10.1016/03894304(94)902097