OPEN ACCESS
The paper looks at the essential components in rail transport such as Axles and Pantograph and gives the detail of the systems used in monitoring their operation. The continuously measured data such as Torque on the main gearbox shaft or load/acceleration on the Pantograph enables diagnostics of such systems on routinely operating trains. Variations from the expected values are being detected early and corrected to avoid compromising passenger safety.A theoretical model is proposed which includes all the components in the traction system and their dynamic influence on each other. The model studies the traction system with the view on the interaction between the wheel and the rail interface.The paper discusses the system designed for monitoring the transmitted torque and bending moments in the rail vehicle axle as a mean for identification of any abnormal loading.Pantograph failures due to complex interactions between the overhead line (OHL) and pantograph structure cause significant problems to railway industry worldwide.This paper also describes the design, development and test results from the first fully proven Pantograph Monitoring System which is now deployed on routinely operating trains in the UK.In both applications monitoring data instantly captured by the embedded systems. The system uses two subcomponents: Digital Processing Module (DPM) and the Receiving Signal and Relay Unit (RSRU), which is installed in a secure location inside the carriage. The DPM uses Bluetooth communication to report any unexpected events to the RSRU, which is equipped with an on-board GPRS module to allow instantaneous access and remote interrogation from any location worldwide. The data collected will enable the reliability of the component under operation to be assessed.Any high alarm events are instantaneously transferred to the train to warn the operator and the control centre about potentially harmful event which require immediate attention. This will in turn increase safety of the travelling passengers from any consequences of developing failures.
bluetooth communication, bogie gearbox, condition monitoring, fl at wheel, modelling rail–wheel interaction, monitoring system, pantograph failure, traction system
[1] Cannon, D.F., A report commissioned by the Steering Group of UIC/WEC Joint Research, An International Cross Reference of Rail effects, 2nd edn, UIC Rail Defect Management, 2003.
[2] Mei, T.X. & Ding, X.J., Condition monitoring of rail vehicle suspension based on changes in system dynamic interactions. Vehicle Systems Dynamics, 47(9), pp. 1167–1181, 2009. doi:http://dx.doi.org/10.1080/00423110802553087
[3] Wu, T.X. & Thompson, D.J., A hybrid model for wheel/track dynamic interaction and noise generation due to wheel fl ats, ISVR Technical Memorandum No 859, 2001.
[4] Shimamune, R., Kikuchi, T., Nomoto, H. & Osawa, M., Adoption of articulated structure in AC train, Special edition paper.
[5] Vondrich, J. & Thondel, E., The application of MatLab in engineering education, Department of Mechanics and Materials Science, Faculty of Electrical Engineering, Czech Technical University: Prague.
[6] McDonal d, M. & Richards, A., Vehicle health monitoring on the docklands light railway. Advanced Condition Monitoring Systems of Railways, IEE Colloquim on 4th October 1995, vol. 4, pp. 1–6.
[7] Preston, K.S., Vehicle systems monitoring technology at BR Research. Advanced Con-dition Monitoring Systems of Railways, IEE Colloquim on 4th October 1995, vol. 3, pp. 1–6.
[8] Hayashi, Y., Kojima, T., Tsunashima, H. & Marumo, Y., Real time fault detection of railway vehicles and tracks, Railway Condition Monitoring, The Institution of Engineering and Technology, pp. 20–25, 2006.
[9] Tsunashima, H., Kojima, T., Marumo, Y., Matsumoto, A. & Mizuma, T., Condition monitoring of railway track and driver using in-service vehicle. 4th IET International Conference on Railway Condition Monitoring, pp. 1–6, 2008. doi:http://dx.doi. org/10.1049/ic:20080320
[10] O’Donnell, C., Palacin, R. & Rosinski, J., Pantograph damage and wear monitoring system, Condition Monitoring, The Institution of Engineering and Technology, pp. 178–181, 2006.
[11] Harada, S. & Shunichi, K., Monitoring of overhead contact line based on contact force, Railway Condition Monitoring, The Institution of Engineering and Technology, pp. 188–193, 2006.